You should do the following: Glacier metallic diamond popsocket popsockets phone.
Clean the residing gel from your phone (or case) backside.
How to remove a popsocket from your phone case. Also take the case off of your phone before you try. Use your fingernail to pry the popsocket off of your phone, then hold the adhesive side of the popsocket and turn your water faucet to a low flow on cold. Now remove the otter box phone case.
Carefully place the exposed adhesive to the desired spot. Always go slow and do not force your popsocket off any surface. If you want a popsocket and have one of these cases, you might have to remove them and opt for a plastic case.
After deciding on your ideal position, pull the adhesive sticker gently from one side expose the adhesive. Depends on what the case is made of as well as what kind of adhesive. How to remove a popsocket from your phone case.
In the rare case where your popsocket takes longer to dry, wipe the base gently with a paper towel. Cant you just buy a new one? Work your fingernails under the base of the popsocket, then slowly peel the popsocket off of your phone.
Let your popsocket dry out in the open air. Im using the belkin wireless boost charge 7.5w. Lay it on a paper towel with the sticky side facing up and away from dust particles.
Slide the floss straight down slowly until the popsocket is fully removed. Popsockets are made up of an adhesive base and the top disk that can be popped in and out. Collapse the popsocket by pressing with your finger.
Carefully run the dental floss underneath the popsocket to remove it from the phone case. Make sure your popsocket is flattened and pressed in before you try to remove it. Applying a popsocket on your phone is a simple process.
Detach the sticky base from the case, rinse it underwater, let it dry for not more than 15 minutes, choose a new spot on your phone and stick the popsocket. This can cause the button to break and your popsocket will no longer be usable. The different steps that you will need to remove the pop socket from otterbox.
What to know collapse the sticky popsocket so it’s flat against your device. Never try to remove it before you do that. Remove the layer of the case where the pop socket is mounted.
Try to remove as much of the adhesive by mechanical. The manufacturer claims it can be reused up to 100 times. Collapse your popsocket so that it’s flat against your device.
If it dries any longer, it will lose its stickiness. When removing your popsocket, do not attempt to pry it off from the expandable button! This is the easiest way to remove the pop socket from your device.
If you need to remove a popsocket from your phone, push down on the top of the popsocket to ensure it’s not expanded. It is easy to get the pop socket out of the otterbox case as they are specially designed. Make sure you don’t apply force while removing it, because you might damage your phone color.
Can you remove a popsocket and reuse it? Let it dry for not more than ten minutes. Yes, you can reuse a popsocket;
Take a firm hold of your mobile. Get underneath the base using the nails on your fingers or any of the items listed above. As long as you have stick it on a case at least it would be fine, super glue also works.
If your popsocket is applied directly to your phone, take extra caution to remove it without damaging the phone itself. Carefully pull the popsocket away from the device until it releases. Table of contents [ hide] step 1:
The easiest way to remove it is in this. The top disk is easy to remove, but removing the sticky base can be tricky. Removing a pop socket is very simple and can generally be done by hand.
This way, you create a lever to push away from the phone softly until the base disconnects. Use dental floss carefully run the dental floss underneath the popsocket to remove it from the phone case. It might be a good idea to stick popsocket to a cover, especially if you have bought a cheap stand.
For more details, check how to remove popsocket from phone case. Slide the floss straight down slowly until the popsocket is fully removed. Remove popsocket from otterbox case.
Always go slow and do not force your popsocket off any surface. You just press and turn and pops off easy. Run only the plastic grip of the popsocket under water — if you must, wrap the adhesive in a hand towel to prevent getting.
Keep pressing down firmly on the popsocket for 15 seconds to make sure it attaches securely to. The video shows it charging with the popsocket attached but. Diy phone case life hacks 30 phone diy projects.
Push in the pop socket. If your fingernails won’t fit, try sliding a few inches of dental floss under the popsocket instead. Remove the popsocket and run the plastic grip under cold water.
Move your fingernail underneath and around the disc to pry it away. How do you remove the popsocket? I just got my wireless chrger today and it will only charge wirelessly if i remove the pop socket.
While the gel is sticky, move the popsocket to another device or move it to a different spot on the current device. Gradient marble case marble iphone case marble iphone. Choosing a selection will reload the page.
Pry the popsocket away from the device.